Roving Networks WIFLY GSX Manual de usuario Pagina 23
- Pagina / 60
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
WiFly GSX
www.rovingnetworks.com
WiFlyGSX-um 7/16/2010
809 University Avenue • Los Gatos, CA 95032 • Tel (408) 395-6539 • info@RovingNetworks.com
~ 23 ~
8. Action Commands
$$$ enter command mode Characters are PASSED until this exact sequence
is seen. If any bytes are seen before these chars, or after these chars, in a
250ms window, command mode will not be entered and these bytes will
be passed on to other side.
close disconnect a TCP connection.
exit exit command mode. Exit command mode. “EXIT” will be displayed.
factory RESET Loads factory defaults into the RAM configuration. Note that the
RESET must be capitalized. This command also writes the settings out
to the standard config file. After this command the module then needs to
be rebooted for settings to take effect.
join <ssid> joins the network <ssid>. If network is security enabled you must set the
pass phrase with the set wlan phrase command prior to issuing the join
command
join # <num> join a network from the scan list. <num> is the entry number in the scan
list that is returned from the scan command. If network is security
enabled you must set the pass phrase with the set wlan phrase command
prior to issuing the join command
leave disconnects the module from the currently associated Access Point.
lookup <hostname> performs a DNS query on the supplied hostname.
open <addr> <port> opens a TCP connection to the given IP port and address. If no arguments
are provided, the device will attempt to connect to the stored remote host
IP address and remote port number. <addr> can also be a DNS hostname
and will be resolved if entered.
Ping <g | h | i | addr> <num> ping remote host. Default sends 1 packet. Optional <num> sends <num>
pings at 10 per second.
Ping 10.20.20.12 10 – pings IP address 10 times
ping g pings the gateway, the gateway IP address is loaded if DHCP
is turned on, otherwise it should be set with the set ip gateway <addr>
command
- 1. Overview 4
- Hardware Interface 5
- 2.1. Power 5
- 2.2. Reset 5
- 2.3. UART 5
- 4. WiFly Command Reference 8
- SET Commands 9
- 5.1. Adhoc Parameters 9
- 5.2. Broadcast Parameters 9
- 5.3. COMM Parameters 10
- 5.4. DNS Parameters 11
- 5.5. FTP Parameters 11
- 5.6. IP Parameters 12
- 5.7. Optional Parameters 14
- 5.8. System Parameters 14
- 5.9. Time Server Parameters 15
- 5.10. UART Parameters 16
- 5.11. WLAN Parameters 17
- 6. Get Commands 20
- 7. Status Commands 21
- 8. Action Commands 23
- 9. File IO Commands 24
- 10.2. Wake on Sensor Input 26
- 10.3. Wake on UART 26
- 10.8. Time Stamping Packets 32
- Sending data using UDP 33
- 11.1. Overview 33
- 11.2. UDP Auto Pairing 34
- 11.3. UDP Retry 34
- 12.2. Making Connections 37
- 12.5. Using DNS settings 38
- 13.1.1. Reading a page: 41
- 13.1.2 41
- Posting data to a page: 41
- 13.1.3 41
- Posting binary data: 41
- 15. Adhoc Networking Mode 44
- 15.2. Configuring adhoc mode 45
- 18. Boot-up Timing Values 52
- 19. Supported Access Points 53
- 20. Release Notes 54
Relacionado con productos y manuales para Redes Roving Networks WIFLY GSX
Redes Roving Networks WIFLY GSX Manual de usuario
(84 paginas)
(84 paginas)
Redes Roving Networks WIFLY GSX Manual de usuario
(42 paginas)
(42 paginas)
Redes Roving Networks RN-370 Manual de usuario
(70 paginas)
(70 paginas)
Redes Roving Networks WIFLY GSX Guía de usuario
(122 paginas)
(122 paginas)
T'nB DCC30RM manuály
Uživatelské manuály a uživatelské příručky pro Pouzdra na fotoaparáty T'nB DCC30RM.
Poskytujeme 1 manuály pdf T'nB DCC30RM ke stažení zdarma podle typů dokumentů: Datový list
Comentarios a estos manuales